How do you actually feel on the subject of Tools You Need to Install a New Bathtub ?

Installing a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the job can move quickly; if you have to open up a wall to eliminate the old tub and position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to leave the old bathtub as well as embeded in the brand-new one. Ensure you have actually qualified on your own for the work and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will certainly assist you mount a brand-new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to alter the plan of your previous supply of water pipes.
Your devices as well as material list must comprise the following:
- New Bathtub
- Hammer
- Pipe Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Measuring tape
- Pipe Caps
Preparing for the Installation
To start with, the sustaining frame supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Using the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out level.
To set up taps, fit the bottom of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also check the overflow outlet and also the normal outlet for leaks.
Lastly, deal with the bath paneling as explained in the producer's user's manual. Tiling and also securing around the bathtub ought to wait until the tub has been utilized a minimum of once as this will settle it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The former type must be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, resulting in difficulties with wetness and also possible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealant can fracture relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As a reader on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that topic was a great idea. Be sure to set aside a second to distribute this post if you appreciated it. Thank-you for your time invested reading it.
We've got solutions!
Comments on “Fundamental Plumbing Guide for Installing a Bathtub”